This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

ATSAMDA1J16B-ABTVAO +BOM

ARM Microcontrollers - MCU

Manufacturer:

Microchip Technology, Inc
Mfr.Part #:

ATSAMDA1J16B-ABTVAO
Datasheet:

ATSAMDA1J16B-ABTVAO Datasheet (PDF)
Mask:

661A7
LeadContent:

Pb-FREE
RestrictionLevel:

STANDARD
PackingMedia:

T/R
EDA/CAD Models:

Request Free CAD Models for ATSAMDA1J16B-ABTVAO

Email: [email protected]

Skype: live:.cid.ab6b29428937b76

Tel: +852 95804164

ATSAMDA1J16B-ABTVAO General Description

The SAM DA1 ARM® Cortex®-M0+ -based microcontrollers are operating at 48MHz (45DMIPS). The ATSAMDA1J16B provides 64KB Flash, 8KB SRAM and 2KB RWW Flash. The connectivity peripheral set consists of 6 serial communication modules (SERCOM) that each can be configured to act as a USART, UART, SPI and I²C. Additional connectivity options are provided by the on-chip one channel Inter-IC sound interface (I²S) and the full-speed USB 2.0 embedded host and device.

Supported by MPLAB X IDE and MPLAB Harmony.

Functional Safety
This device supports the ISO 26262 (ASIL B) functional safety standard.
· The Functional Safety Manual, FMEDA and information on the Diagnostic Software are available under NDA through the request form on the 32-bit Microcontrollers Functional Safety web page.
· Learn more about 32-bit MCUs with Functional Safety capabilities including device hardware and certified software libraries.

Key Features

ARM Cortex-M0+ CPU running at up to 48MHz
Single-cycle hardware multiplier
Micro trace buffer
64KB in-system self-programmable Flash
2KB Read-While-Write (RWW) Flash section
8KB SRAM memory
Power-on reset (POR) and brown-out detection (BOD)
Internal and external clock options with 48MHdigital frequency locked loop (DFLL48M) and 48MHto 96MHz
fractional digital phase locked loop (FDPLL96M)
External interrupt controller (EIC)
16 external interrupts
One non-maskable interrupt
Two-pin serial wire debug (SWD) programming, test and debugging interface
Idle and standby sleep modes
SleepWalking peripherals
8-channel direct memory access controller (DMAC)
12-channel event system
One 16-bit TC with compare/capture channels
One 8-bit TC with compare/capture channels
One 32-bit TC with compare/capture channels, by using two TCs
Up to four compare channels with optional complementary output
Generation of synchronized pulse width modulation (PWM) pattern across port pins
Deterministic fault protection, fast decay and configurable dead-time between complementary output
Dithering for enhancing resolution with up to 5-bit and reduce quantization error
32-bit real time counter (RTC) with clock/calendar function
Watchdog timer (WDT)
CRC-32 generator
Device 2.0 and reduced-host low speed and full speed
Flexible end-point configuration and management with dedicated DMA channels
On-chip transceivers including pull-ups and serial resistors
Crystal-less operation in device mode
USART with full-duplex and single-wire half-duplex configuration
I2C up to 3.4MHz
SPI
LIN Client
One two-channel inter-IC sound (I2S) interface
Differential and single-ended input
1/2x to 16x programmable gain stage
Automatic offset and gain error compensation
Oversampling and decimation in hardware to support 13-, 14-, 15- or 16-bit resolution
10-bit, 350ksps digital-to-analog converter (DAC)
Two analog comparators (AC) with window compare function
Up to 256-channel capacitive touch and proximity sensing
52 GPIO pins
64-pin TQFP
2.7V to 3.63V
–40 to +105°C

Microchip Technology, Inc Original Stock

Specifications

Mask	661A7	LeadContent	Pb-FREE
RestrictionLevel	STANDARD	PackingMedia	T/R
TempLevel	Special	TempRange	-40C to +105C
Stage	REL	LeadCount	64
ProductClassDescription	Special Test Temp, Tape & Reel	PackingMediaDescription	Tape and reel
Weight	0.0005746667