Payment Method
TMAG5170A2QDGKT +BOM
High-precision, linear 3D Hall-effect sensor with SPI bus interface
8-VSSOP-
Manufacturer:
Texas Instruments
-
Mfr.Part #:
TMAG5170A2QDGKT
-
Datasheet:
-
Type:
Linear Hall-Effect Sensor With SPI
-
Operating Supply Current:
3.4 mA
-
Maximum Output Current:
2 mA
-
Operating Point Min/Max:
+/- 75 mT to +/- 300 mT
-
EDA/CAD Models:
Send all BOMs to [email protected], or fill out the form below for a quote on TMAG5170A2QDGKT. Guaranteed response within 12hr.
Availability: 8914 PCS
Please fill in the short form below and we will provide you the quotation immediately.
TMAG5170A2QDGKT General Description
The TMAG5170 is a high-precision linear 3D Hall-effect sensor designed for a wide range of industrial and personal electronics applications. The high level of integration offers flexibility and accuracy in a variety of position sensing systems. This device features 3 independent Hall sensors at X, Y, and Z axes.
A precision signal-chain along with an integrated 12-bit ADC enables high accuracy and low drift magnetic field measurements while supporting a sampling of up to 20 ksps. On-chip temperature sensor data is available for system-level drift compensation.
Integrated angle calculation engine (CORDIC) provides full 360° angular position information for both on-axis and off-axis angle measurement topologies. The angle calculation is performed using two user-selected magnetic axes. The device features magnetic gain and offset correction to mitigate the impact of system mechanical error sources.
The TMAG5170 can be configured through the SPI to enable any combination of magnetic axes and temperature measurements. Multiple sensor conversion schemes and SPI read frames help optimize throughput and accuracy. A dedicated ALERT pin can act as a system interrupt during low power wake-up and sleep mode, and can also be used by a microcontroller to trigger a new sensor conversion.
The TMAG5170 offers multiple diagnostics features to detect and report both system and device-level failures. The SPI communication features a user-enabled cyclic redundancy check to enhance the data integrity.
The device is offered in two different orderables to support wide magnetic fields ranges from ±25mT to ±300mT.
The device performs consistently across a wide ambient temperature range of –40°C to +150°C.
Key Features
- High-precision linear 3D Hall-effect sensor to optimize position sensing speed and accuracy:
- Linear measurement total error: ±2.6% (maximum at 25°C)
- Sensitivity temperature drift: ±2.8% (maximum)
- 20-Ksps conversion rate for single axis
- 10-MHz serial peripheral interface (SPI) with cyclic redundancy check (CRC)
- Built-in temperature sensor with < ±2°C error
- Independently selectable X, Y, and Z magnetic ranges:
- TMAG5170A1: ±25, ±50, ±100 mT
- TMAG5170A2: ±75, ±150, ±300 mT
- 5-nA (typical) deep sleep mode current
- Autonomous wake-up and sleep mode for threshold detection consuming only 1.5 µA
- ALERT function to initiate sensor conversion or indicate conversion complete
- Integrated diagnostics for fault detection
- Integrated angle CORDIC calculation with gain and offset adjustment
- 2.3-V to 5.5-V supply voltage range
- Operating temperature range: –40°C to +150°C
Specifications
Product Category | Board Mount Hall Effect / Magnetic Sensors | Type | Linear Hall-Effect Sensor With SPI |
Operating Supply Current | 3.4 mA | Maximum Output Current | 2 mA |
Operating Point Min/Max | +/- 75 mT to +/- 300 mT | Release Point Min/Max (Brp) | - |
Operating Supply Voltage | 2.3 V to 5.5 V | Minimum Operating Temperature | - 40 C |
Maximum Operating Temperature | + 150 C | Mounting Style | SMD/SMT |
Product | Linear Hall Effect Sensors | Product Type | Hall Effect / Magnetic Sensors |
Sensitivity | 1308 mT | Factory Pack Quantity | 250 |
Subcategory | Sensors | Supply Voltage - Max | 5.5 V |
Supply Voltage - Min | 2.3 V | Termination Style | SMD/SMT |
Service Policies and Others
After-Sales & Settlement Related
For alternative payment channels, please reach out to us at:
[email protected]Shipping Method
AVAQ determines and packages all devices based on electrostatic discharge (ESD) and moisture sensitivity level (MSL) protection requirements.
365-Day Product
Quality Guarantee
We promise to provide 365 days quality assurance service for all our products.
In Stock: 8,914
Minimum Order: 1
Qty. | Unit Price | Ext. Price |
---|---|---|
1+ | $2.315 | $2.32 |
250+ | $0.896 | $224.00 |
500+ | $0.866 | $433.00 |
1000+ | $0.850 | $850.00 |
The prices below are for reference only.