This website uses cookies. By using this site, you consent to the use of cookies. For more information, please take a look at our Privacy Policy.

Images are for reference only,

See Technical Specifications

ATSAMB11-MR210CA +BOM

This module is designed for seamless Bluetooth communication, supporting 802.15.1 standards for reliable wireless connections

Manufacturer:

Microchip Technology
Mfr.Part #:

ATSAMB11-MR210CA
Datasheet:

ATSAMB11-MR210CA Datasheet (PDF)
Series:

SmartConnect
Programmabe:

Not Verified
RF Family/Standard:

Bluetooth
Protocol:

Bluetooth v4.1
EDA/CAD Models:

Request Free CAD Models for ATSAMB11-MR210CA

ATSAMB11-MR210CA General Description

Catering to the needs of battery-powered devices, the ATSAMB11-MR210CA boasts impressive energy efficiency, ensuring prolonged operational performance. Thanks to its ARM Cortex-M0 processor, the module delivers robust processing power for seamless application execution and efficient communication handling. Moreover, its support for various Bluetooth profiles and protocols guarantees compatibility with a wide spectrum of devices and systems, further enhancing its versatility. With built-in security measures, this module prioritizes data integrity and secure communications, catering to the stringent security requirements of modern applications

Key Features

Core
– ARM® Cortex®-M3 revision 2.0 running at up to 64 MHz
– Memory Protection Unit (MPU)
– Thumb®-2 instruction set
Pin-to-pin compatible with AT91SAM7S series (48- and 64-pin versions)
Memories
– From 64 to 256 Kbytes embedded Flash, 128-bit wide access, memory accelerator, single plane
– From 16 to 48 Kbytes embedded SRAM
– 16 Kbytes ROM with embedded bootloader routines (UART, USB) and IAP routines
– 8-bit Static Memory Controller (SMC): SRAM, PSRAM, NOR and NAND Flash support
– Memory Protection Unit (MPU)
System
– Embedded voltage regulator for single supply operation
– Power-on-Reset (POR), Brown-out Detector (BOD) and Watchdog for safe operation
– Quartz or ceramic resonator oscillators: 3 to 20 MHz main power with Failure Detection and optional low power 32.768 kHz for RTC or device clock
– High precision 8/12 MHz factory trimmed internal RC oscillator with 4 MHz default frequency for device startup. Inapplication trimming access for frequency adjustment
– Slow Clock Internal RC oscillator as permanent low-power mode device clock
– Two PLLs up to 130 MHz for device clock and for USB
– Temperature Sensor
– Up to 22 peripheral DMA (PDC) channels
Low Power Modes
– Sleep and Backup modes, down to 1.8 µA in Backup mode
– Ultra low power RTC
Peripherals
– USB 2.0 Device: 12 Mbps, 2668 byte FIFO, up to 8 bidirectional Endpoints. On-Chip Transceiver
– Up to 2 USARTs with ISO7816, IrDA®, RS-485, SPI, Manchester and Modem Mode
– Two 2-wire UARTs
– Up to 2 Two Wire Interface (I2C compatible), 1 SPI, 1 Serial Synchronous Controller (I2S), 1 High Speed Multimedia Card Interface (SDIO/SD Card/MMC)
– Up to 6 Three-Channel 16-bit Timer/Counter with capture, waveform, compare and PWM mode. Quadrature Decoder Logic and 2-bit Gray Up/Down Counter for Stepper Motor
– 4-channel 16-bit PWM with Complementary Output, Fault Input, 12-bit Dead Time Generator Counter for Motor Control
– 32-bit Real-time Timer and RTC with calendar and alarm features
– Up to 15-channel, 1Msps ADC with differential input mode and programmable gain stage
– One 2-channel 12-bit 1Msps DAC
– One Analog Comparator with flexible input selection, Selectable input hysteresis
– 32-bit Cyclic Redundancy Check Calculation Unit (CRCCU)
– Write Protected Registers
– Up to 79 I/O lines with external interrupt capability (edge or level sensitivity), debouncing, glitch filtering and on-die Series Resistor Termination
– Three 32-bit Parallel Input/Output Controllers, Peripheral DMA assisted Parallel Capture Mode
Packages
– 100-lead LQFP, 14 x 14 mm, pitch 0.5 mm/100-ball TFBGA, 9 x 9 mm, pitch 0.8 mm
– 64-lead LQFP, 10 x 10 mm, pitch 0.5 mm/64-pad QFN 9x9 mm, pitch 0.5 mm
– 48-lead LQFP, 7 x 7 mm, pitch 0.5 mm/48-pad QFN 7x7 mm, pitch 0.5 mm

Specifications

Series	SmartConnect	Programmabe	Not Verified
RF Family/Standard	Bluetooth	Protocol	Bluetooth v4.1
Frequency	2.4GHz	Power - Output	4dBm
Sensitivity	-96dBm	Serial Interfaces	I2C, SPI, UART
Antenna Type	Integrated, Chip	Memory Size	256kB Flash, 128kB ROM, 128kB RAM
Voltage - Supply	2.3V ~ 3.6V	Current - Receiving	4mA
Current - Transmitting	3mA	Mounting Type	Surface Mount
Base Product Number	ATSAMB11